Genesis G70 Horsepower and how to get more of it - Genesis G70 Forum
 
LinkBack Thread Tools
post #1 of 6 (permalink) Old 05-14-2019, 09:12 AM Thread Starter
Junior Member
 
Join Date: Apr 2019
Posts: 23
Genesis G70 Horsepower and how to get more of it

What are everyone's suggestions for getting more power from the 3.3T?

I know 365-hp is plenty, but I'm curious about aftermarket support.

I'd like to build a resource thread here with info about aftermarket exhausts, air intakes, etc.

Obvious things like K&N air filter:
https://www.knfilters.ca/search/apps...70&engine=3.3L

Does anyone make a cone filter for it yet?

And what about engine tuning? Does anyone offer chip tuning for the 3.3T yet?
St00k is offline  
post #2 of 6 (permalink) Old 05-15-2019, 06:33 PM
Junior Member
 
Join Date: May 2019
Posts: 6
Heard great things about the BMS intake from Kia Stinger owners. Some have been installed in the G70, here's one of them. My 3.3T Sport should be joining



Features and Benefits

• Adds Horsepower
• Improved throttle response
• Improved engine sound
• Includes heat shields
• Looks great under the hood
• Cleanable and reusable filters
• Easy installation and removal
• Made in the USA

Featuring high quality K&N cone filters the BMS Stinger intake offers the highest possible flow in an attractive and easy to install package. The BMS Stinger intake removes the restrictions within the factory system while retaining the factory cold air ducting, heat isolating airbox bottom, and high flow turbo inlet fittings. In addition a stylish top half shroud is included to protect the intake from radiant engine heat.The result is dramatically improved performance, throttle response, and sound. You'll finally get to hear what is going on under the hood! And the more boost you run the higher the performance gains.

This intake has been extensively tested on the BMS development Stinger running [email protected] in the 1/4 mile and 148mph half mile traps.

Installation is easy taking only a few minutes to install and remove right in your driveway. The high flow K&N filters can be cleaned every 15-20k miles for optimal performance. Made in the USA.
marco.k is offline  
post #3 of 6 (permalink) Old 05-19-2019, 09:40 PM
Senior Member
 
Join Date: Jun 2016
Posts: 294
Quote:
Originally Posted by marco.k View Post
Heard great things about the BMS intake from Kia Stinger owners. Some have been installed in the G70, here's one of them. My 3.3T Sport should be joining



Features and Benefits

Adds Horsepower
Improved throttle response
Improved engine sound
Includes heat shields
Looks great under the hood
Cleanable and reusable filters
Easy installation and removal
Made in the USA

Featuring high quality K&N cone filters the BMS Stinger intake offers the highest possible flow in an attractive and easy to install package. The BMS Stinger intake removes the restrictions within the factory system while retaining the factory cold air ducting, heat isolating airbox bottom, and high flow turbo inlet fittings. In addition a stylish top half shroud is included to protect the intake from radiant engine heat.The result is dramatically improved performance, throttle response, and sound. You'll finally get to hear what is going on under the hood! And the more boost you run the higher the performance gains.

This intake has been extensively tested on the BMS development Stinger running [email protected] in the 1/4 mile and 148mph half mile traps.

Installation is easy taking only a few minutes to install and remove right in your driveway. The high flow K&N filters can be cleaned every 15-20k miles for optimal performance. Made in the USA.
About that 1/4 mile time, has any owners confirmed it for themselves? 3.3's run 12.8 stock, shaving off 1 second is quite a lot.
FastG is offline  
 
post #4 of 6 (permalink) Old 05-24-2019, 05:57 PM
Junior Member
 
Join Date: Feb 2019
Posts: 1
I'm looking into getting this!

Have you looked into the JB4 from Burger?
SuperNuprin is offline  
post #5 of 6 (permalink) Old 05-27-2019, 02:54 PM
Senior Member
 
Join Date: Jun 2016
Posts: 294
@SuperNuprin I was just looking into that and am closer to getting it.

I mean, who's really going to turn down the claimed "462 horsepower and 531 pound feet of torque – at the wheels…"

Have you or anyone you know in the community went for it by now? Contemplating REV3/BMS
FastG is offline  
post #6 of 6 (permalink) Old 06-04-2019, 01:31 PM
Junior Member
 
Join Date: May 2019
Posts: 18
Does anyone know if we can expect to see lightweight parts come from Seibon or similar CF parts makers?
Ricky.M is offline  
Reply

Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



Posting Rules  
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome